Paget Trading Ltd 9159 User Manual

[. . . ] near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement. If the monitor falls, it can injure a person and cause serious damage to the appliance. Use only a cart or stand recommended by the manufacturer or sold with the monitor. If you mount the monitor on a wall or shelf, use a mounting kit approved by the manufacturer and follow the kit instructions. [. . . ] Due to the nature of the LCD screen, an afterimage of the previous screen may remain after switching the image when the same image has been displayed for a long time. The monitor will slowly recover from this. BEFORE YOU OPERATE THE MONITOR FEATURES 19' (48cm) Wide screen TFT Color LCD Monitor Crisp, Clear Display for Windows Recommened Resolutions: 1440 X 900@60Hz EPA ENERGY STAR® Dual Input (DVI + Analog) Ergonomic Design Space Saving, Compact Case Design CHECKING THE CONTENTS OF THE PACKAGE The product package should include the following items: 1. LCD Monitor Owner's Manual Power Cord D-Sub Cable DVI Cable External Adapter 4 INSTALLATION INSTRUCTIONS SWIVEL BASE Install Remove Figure 1 Installing and Removing the Swivel Base POWER CORD Power Source: 1. Make sure that the power cord is the correct type required in your area. This LCD monitor has an External universal power supply that allows operation in either 100/120V AC or 220/240V AC voltage area (No user adjustment is required. ) 3. Connect the AC-power cord into your LCD monitor's External Adapter input socket, and then plug the other end of External adapter to LCD monitor's DC-power-input. The AC-power cord may be connected to either a wall power outlet or the power outlet socket on your PC, depending on the type of power cord supplied with your LCD monitor. NOTES A certified power supply cord has to be used with this equipment. The relevant national installation and/or equipment regulations shall be considered. A certified power supply cord not lighter than ordinary polyvinyl chloride flexible cord according to IEC 60227 (designation H05VV-F 3G 0. 75mm2 or H05VVH2-F2 3G 0. 75mm2) shall be used. Alternative a flexible cord be of synthetic rubber according to IEC 60245 (designation H05RR-F 3G 0. 75mm2) shall be used. 5 CONTROLS AND CONNECTORS Turn off your computer before performing the procedure below. Connect the power adapter dc cable to the DC-In port on the back of the monitor. Stubborn stains may be removed with a cloth lightly dampened with a mild detergent solution. Never use strong solvents such as thinner, benzene, or abrasive cleaners, since these will damage the cabinet. As a safety precaution, always unplug the monitor before cleaning it. 9 HOW TO ADJUST A SETTING 1. Once the desired function is highlighted, press the MENU-button to activate it. If the function selected has a sub-menu, press or again to navigate through the sub-menu functions. Once the desired function is highlighted, press MENU-button to activate it. If you want to adjust any other function, repeat steps 2-3. Figure 5 The OSD Message 10 ADJUSTING THE PICTURE The descriptions for function control LEDS Main Menu Item Main Sub Sub Menu Menu Menu Item Icon Icon Contrast Luminance Brightness Focus Clock H. User / Red User / Green User / Blue Input Select Analog Digital N/A N/A N/A N/A N/A Backlight Adjustment Adjust Picture Phase to reduce Horizontal-Line noise Adjust picture Clock to reduce Vertical-Line noise. Select input signal from analog source (D-Sub) Select input signal from digital source (DVI) Description Contrast from Digital-register. Image Setup Image Position 11 Main Sub Main Sub Menu Menu Menu Menu Item Item Icon Icon Description H. Position OSD Timeout Language Information Language Information N/A N/A Adjust the horizontal position of the OSD. Adjust the verticalposition of the OSD. Show the resolution, H/V frequency and input port of current input timing. [. . . ] With a wrong phase adjustment the picture has horizontal disturbances in light picture. For FOCUS and CLOCK adjustment use 'dot-pattern' or win 95/98 shutdown mode pattern. Problem & Question Power LED is not on 14 ERROR MESSAGE & POSSIBLE SOLUTION CABLE NOT CONNECTED : 1. Check that the signal-cable is properly connected , If the connector is loose, tighten the connector's screws. [. . . ]